行業資訊

攤鋪機養護注意事項以及問題預防

來源：http://lehuoaijia.com/ 日期：2022-08-01

攤鋪機在施工中能不能順利的勝任，主要取決于平時的維修保養是否到位！下面就來簡單認識一下吧。

Whether the paver can be successfully competent in construction mainly depends on whether the usual maintenance is in place! Let's get to know each other briefly.

1.每班工作前，操作人員須檢查各控制系統及安全防護裝置工作正常，并確保所有防護裝置均已安裝。

1. Before each shift, the operator must check that all control systems and safety protective devices work normally, and ensure that all protective devices have been installed.

2.每天工作前，檢查所有油脂加注點的潤滑情況并根據情況加注油脂。

2. Before working every day, check the lubrication of all grease filling points and add grease according to the situation.

3.每次開機前，將所有開關或操縱桿，電位器旋鈕放置中位，將油門開關或操縱桿放置在怠速位置。如安全防護裝置或其他零部件檢查出故障，會影響機器的安全運轉，應立即排除。

3. Before each startup, place all switches or control levers and potentiometer knobs in the middle position, and place the throttle switch or control lever in the idle position. If the safety protection device or other parts fail, which will affect the safe operation of the machine, it should be eliminated immediately.

4.濟南攤鋪機出租廠家提醒您，一旦有異常噪音及故障影響操作，須立即停機。

4. Jinan paver rental manufacturer reminds you that once there is abnormal noise and failure affecting the operation, you must stop the machine immediately.
濟南攤鋪機出租

5.攤鋪機租賃每一年應讓專業人員進行檢測并書面記錄檢測結果。

5. Every year when the paver is leased, professional personnel should be allowed to test and record the test results in writing.

此外要注意一些問題的出現與預防：

In addition, we should pay attention to the emergence and prevention of some problems:

輸出液壓油達不到預定參數：檢查各支管壓力和油泵輸出壓力以及測量油泵和馬達的轉速。接壓力表測壓力，若泵、馬達損壞則進行更換。

The output hydraulic oil cannot reach the predetermined parameters: check the pressure of each branch pipe and the output pressure of the oil pump, and measure the speed of the oil pump and motor. Connect the pressure gauge to measure the pressure. If the pump and motor are damaged, replace them.

油溫過高：檢查油箱內油量；濾油器濾芯污染情況；泵和馬達運轉狀態。

High oil temperature: check the oil quantity in the oil tank; Pollution of oil filter element; Pump and motor operation status.

補充加油；更換濾油器濾芯；檢查溢流閥工作情況，視情況對其進行更換；更換泵和馬達已損部件。

Refueling; Replace the oil filter element; Check the working condition of the overflow valve and replace it as appropriate; Replace the damaged parts of the pump and motor.

噪聲大：檢查油箱中的油是否有氣泡產生；管路固定處是否松動；泵和馬達工作狀態。油不足補充加油；加固松動連接處防止共振；元件損壞應及時更換；排除液壓回路中的氣體。

Loud noise: check whether there are bubbles in the oil tank; Whether the fixed part of the pipeline is loose; Pump and motor operating conditions. Refuel if the oil is insufficient; Reinforce the loose connection to prevent resonance; Replace the damaged components in time; Remove the gas from the hydraulic circuit.

我們有維修人員和經驗豐富的技術指導，有任何設備配件問題，您這邊都可以聯系我們http://lehuoaijia.com，為您的工程保駕護航。

We have maintenance personnel and experienced technical guidance. If you have any questions about equipment accessories, you can contact us here http://lehuoaijia.com , escort your project.

上一條：壓路機租賃的這幾點你需要注意

下一條：公路養護機械設備故障產生因素